Sensor Hardware Engineer – Tactile, Audio & Vision (human)
- Level
- Mid
- Work type
- On-site · Munich
Not stated in the posting: salary, visa.
Open. First seen 18 November 2026.
About the role
You own the sensing stack, from first signal to production release. NEURA Robotics builds robots that have to feel, hear and see. A large part of that sits in the humanoid hand: tactile sensing in fingertips and palm, force and torque in the joints, all in a space that leaves no room for a comfortable design.
Around it come microphone arrays for speech and acoustic events, and camera and depth modules that survive vibration, heat and tight packaging. You take these sensors from concept to a characterized, calibrated, production-released design, together with our electronics, firmware, perception and mechanical engineers.
Your mission & challenges
- Sensor architecture: You select, specify and benchmark tactile, acoustic and optical sensors against what the robot actually needs: resolution, noise floor, latency, power, cost and supply risk.
- Tactile and force sensing for the hand: You design and integrate tactile arrays and force/torque sensing for fingertips, palm and joints, including the low-noise analog front-ends behind them. You make sure they fit, mechanically and thermally.
- Characterization and calibration: You run the measurement campaigns, build the fixtures, and turn your lab procedure into something production can repeat on every unit.
- Bring-up and debugging: You lead sensor bring-up in the lab and trace problems end-to-end, from a noisy supply rail through the front-end to a perception result that looks wrong.
- Hardware design and transfer to production: You design or co-design the sensor PCBAs and flex assemblies (depending on the product, both happen here). You own the manufacturing documentation and work with EMS partners and sensor vendors to release them for series production.
- Firmware and perception interface: Firmware development is not your main job, but you can read it, write enough of it to bring a sensor up, and support the firmware team on drivers, timestamping and synchronization. With perception, you agree on what the data has to look like for their models to work.
What we can look forward to
You know sensors inside out, and you trust measurements over datasheets. You are hands-on, as comfortable with an analog front-end schematic as with a measurement setup, and you treat characterization and calibration as part of the design.
- Education: Degree in Electrical Engineering, Electronics, Mechatronics, Physics or a comparable field.
- Experience: 3+ years with sensor hardware, with ownership from concept through characterization to production release.
- Analog & mixed-signal design: Low-noise front-end design with instrumentation and charge amplifiers, capacitive and bridge conditioning, ADC selection, grounding and shielding.
- Modalities: Hands-on experience with at least two of the three modalities (tactile/force, audio, vision/depth), and the willingness to own all three.
- Sensor interfaces & timing: I²S/TDM/PDM, MIPI CSI-2, SPI, I²C, and synchronization across sensors.
- Measurement in practice: You design the experiment, build the fixture, and know a real effect from a measurement artifact.
- PCB & flex design: Working knowledge of Altium Designer or comparable tools for compact sensor assemblies.
- Languages: Fluent English; good German is a strong advantage.
A strong plus:
- Robotic hands or grippers: Tactile skins, slip detection, sensing in very tight packaging.
- Acoustics or optics: Arrays, beamforming, anechoic measurement, or lens selection, illumination and depth.
- Sensors in harsh conditions: Vibration, thermal cycling, cable and flex fatigue.
What this role asks for
Particular to this role
Altium · PCB Design
Rare in Neura Robotics's other 147 open postings.
Standard for embedded / hardware roles
Embedded Systems
Common in embedded / hardware postings at any company.
Compared with Neura Robotics's other open jobs.
The team: Electrical Engineering HIRES STEADILY
This role is one of 5 open in Electrical Engineering. 1 was posted in the last 30 days and the oldest in May: a team that hires all year rather than one being built.
WHAT THE TEAM WORKS WITH, ACROSS ITS POSTINGS
Embedded Systems (5 of 5), CAN bus (3 of 5), Altium (2 of 5), C (2 of 5), C++ (2 of 5), PCB Design (2 of 5)
OTHER ROLES ON THIS TEAM
- Prototype & Cabling Engineer (human) posted May 11
- PCB Design & Electrical Engineer (human) posted May 11
- Hardware Architect - Cognitive Robotics (human) posted May 11
- Embedded & Firmware Engineer (human) posted May 11
From the team and dates on Neura Robotics's own job board.
Similar jobs
- Hardware Engineer at Weekday AI
Shares 3 skills: Altium, PCB Design, Embedded Systems · same seniority - (Mid/Senior) Robotics or Mechatronics Technician/Engineer (m/f/d) at Agile Robots SE
Shares 3 skills: Altium, PCB Design, Embedded Systems · same city - Senior Hardware Engineer, Vaasa at Skeleton Technologies
Shares 3 skills: Altium, PCB Design, Embedded Systems - Electrical Hardware Engineer (multiple levels available) at Muon Space
Shares 3 skills: Altium, PCB Design, Embedded Systems · same seniority - Hardware Engineer at Root Access
Shares 3 skills: Altium, PCB Design, Embedded Systems · same seniority - Robotic Service Engineer / Technician (human) at Neura Robotics
Also at this company
More jobs like this
Is this your posting? Email [email protected] to have it removed.